北京沙尘天气与源地气象条件的关系

本介绍了影响北京地区沙尘天气的沙尘源地,沙尘暴发生的条件和传输路径,分析了沙尘暴源地的气候要素特征及其对北京地区沙尘天气的影响,说明了北京沙尘天气发生和加剧的原因,影响北京地区沙尘天气的境外源地主要位于哈萨克斯坦,俄罗斯以及蒙古国境内,境内源地主要位于内蒙古和新疆,以及甘肃和青海的部分地区,沙尘天气发生必须具备三个条件：沙源,大风,气流辐合（垂直对流）,有沙源不一定起沙,但无沙源一定不起沙,沙尘暴源地的气候特征主要表现为冬季寒冷,夏季炎热,全年降水稀水,影响北京的沙尘传输路径,最主要的有两条,即西路传输和北路传输,北京沙尘天气与沙尘暴源地的春季降水比较结果表明,北京地区沙尘暴和浮尘天气发生次数与沙尘源区春季大气降水量有比较显的负相关关系,北京扬沙天气的发生与沙源区冬春季降水量相关关系不显,说明北京扬沙天气起因与源区降水没有明显的关系,北京扬沙天气主要受本地的自然条件和人为活动的影响。     

Characterization of Dust Storms to Hong Kong in April 1998

In April 1998, two intense dust storms were generated in CentralAsia and transported eastward across East Asia (15 and 19 April). This article presents the chemical characterization ofHong Kong (HK) aerosols during the dust storms. During the 15 Aprildust storm, hourly respiratory suspended particles (RSP)(particle diameter smaller than 10 m) concentrationsmonitored at 7 sites in Hong Kong reached the peak valuessynchronously between 9 and 11 a.m. on 17 April, in which thehighest concentration was 267 g m^-3. Analysis ofthe RSP samples showed that concentrations of crustalelements (Ba, Ca, Cd, Cr, Fe, Mg, K⁺) and anthropogenicspecies (As, Ni, Pb, Zn, NH₄ ⁺, NO₃ ^-,SO₄ ^2- and total carbon) were substantiallyenhanced. Enhancement of these species was more than afactor of 2 to 14 relative to the non dust period. The totalcarbon content was high, at 59 g m^-3 (notincluding carbonate), and the enrichment factors of Asand Pb on 17 April were 122 and 117, respectively. Thisimplied that anthropogenic materials together with mineraldust were transported to HK from Mainland China. Based onmaterial balance calculations, mineral dust contributed41% to the observed RSP mass on 17 April, which was 2 times thatof the nondust sample (22%). From the 5-day backwardtrajectory analysis, this storm was transported directlyfrom Northwest China to HK. However, there was nocorresponding observation for the 19 April dust stormaerosol. Consequently, 15 April storm had stronger impact onHK's atmosphere than 19 April storm. Compared to the HK AirQuality Objective, 15 April dust storm did not cause seriousair pollution in HK.     

Post-explosion observations of experimental mine and laboratory coal dust explosions

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine (LLEM), and after laboratory explosions in the PRL 20-L chamber and the Fike 1 m³ chamber. The dusts studied included both high- and low-volatile bituminous coals. Low temperature ashing for 24 h at 515 °C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as, or higher than the initial incombustible content. The MSHA alcohol coking test was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared with the initial dust loadings to determine the transport distance of dust during an explosion. All these data will be useful in future forensic investigations of accidental dust explosions in coal mines, or elsewhere.     

Determination of turbulent burning velocities of dust air mixtures with the open tube method

Correlating turbulent burning velocity to turbulence intensity and basic flame parameters-like laminar burning velocity for dust air mixtures is not only a scientific challenge but also of practical importance for the modelling of dust flame propagation in industrial facilities and choice of adequate safety strategy. The open tube method has been implemented to measure laminar and turbulent burning velocities at laboratory scale for turbulence intensities in the range of a few m/s. Special care has been given to the experimental technique so that a direct access to the desired parameters was possible minimising interpretation difficulties. In particular, the flame is propagating freely, the flame velocity is directly accessible by visualisation and the turbulence intensity is measured at the flame front during flame propagation with special aerodynamic probes. In the present paper, those achievements are briefly recalled. In addition, a complete set of experiments for diametrically opposed dusts, starch and aluminium, has been performed and is presented hereafter. The experimental data, measured for potato dust air mixtures seem to be in accordance with the Bray Gülder model in the range of 1.5 m/s<u′<3.5 m/s. For a further confirmation, the measurement range has been extended to lower levels of turbulence of u′<1.5 m/s. This could be achieved by changing the mode of preparation of the dust air mixture. In former tests, the particles have been injected into the tube from a pressurised dust reservoir; for the lower turbulence range, the particles have been inserted into the tube from above by means of a sieve–riddler system, and the turbulence generated from the pressurised gas reservoir as before. For higher levels of turbulence, aluminium air mixtures have been investigated using the particle injection mode with pressurised dust reservoir. Due to high burning rates much higher flame speeds than for potato dusts of up to 23 m/s have been obtained.     

Influence of the oxide content on the ignition energies of aluminium powders

Some results of determination of ignition energies for an aluminium powder with various oxide contents are presented. Common use of processes like high-speed cutting produce explosive dust clouds, so that we focused this study on hazard of metallic powders. An industrial aluminium powder has been used for this work. An original process, based on the principle of electrochemical anodisation, has been developed to increase, under control, the oxide coating of particles.

The sensitivity study to spark ignition was performed in an Hartmann explosion tube of 1.3L. The Langlie test method was applied to evaluate the energies leading to a probability of ignition of 50% (E₅₀) of the selected samples. The results confirm that the ignition energies increase with the oxide content of the powder.     

Moderation of dust explosions

Inherent safety is a proactive approach to process safety in which hazards are removed or minimized so as to reduce risk without engineered (add-on) or procedural intervention. Four basic principles are available to attain an inherently safer design—minimization, substitution, moderation, and simplification. The subject of the current paper is the principle of moderation as it applies to the prevention and mitigation of dust explosions.

Moderation can be achieved by processing a material under less severe operating conditions or by processing the material in a less hazardous form. With respect to the latter approach, it may be possible to alter the composition of a dust by admixture of solid inertants, or to increase the dust particle size so as to decrease its reactivity. Additionally, avoidance of the formation of hybrid mixtures of explosible dusts and flammable gases is an application of moderation of the material hazard.

Several examples are given for each of the above three forms of moderation. The discussion on admixture of solid inertants includes examples from the following industrial applications: (i) refractory materials manufacturing, (ii) food processing, (iii) power generation, (iv) industrial recycling, and (v) foundry shell mold fabrication. The importance of particle size consideration is explained first from the perspective of engineering tools such as the Dow Fire & Explosion Index, and professional guidance on the definition of a dust and suitable particle sizes for explosibility testing. Industrial examples are then drawn from the following areas: (i) rubber recycling and textile manufacturing, (ii) industrial recycling, (iii) wood processing, (iv) dry additive handling (polyethylene facility), (v) polyethylene production, (vi) carbon block recycling, and (vii) coal mining. The concluding discussion on hybrid mixtures includes brief cases from the process safety literature.     

Ignitability characteristics of aluminium and magnesium dusts that are generated during the shredding of post-consumer wastes

The authors investigated the ignitability of aluminium and magnesium dusts that are generated during the shredding of post-consumer waste. The relations between particle size and the minimum explosive concentration, the minimum ignition energy, the ignition temperature of the dust clouds, etc. the relation between of oxygen concentration and dust explosion, the effect of inert substances on dust explosion, etc. were studied experimentally.

The minimum explosive concentration increased exponentially with particle size. The minimum explosive concentrations of the sample dusts were about 170 g/m³ (aluminium: 0–8 μm) and 90 g/m³ (magnesium: 0–20 μm). The minimum ignition energy tended to increase with particle size. It was about 6 mJ for the aluminium samples and 4 mJ for the magnesium samples. The ignition temperature of dust clouds was about 750 °C for aluminium and about 520 °C for magnesium. The lowest concentrations of oxygen to produce a dust explosion were about 10% for aluminium and about 8% for magnesium. A large mixing ratio (more than about 50%) of calcium oxide or calcium carbonate was necessary to decrease the explosibility of magnesium dust. The experimental data obtained in the present investigation will be useful for evaluating the explosibility of aluminium and magnesium dusts generated in metal recycling operations and thus for enhancing the safety of recycling plants.     

STORM WATER MANAGEMENT: THE CONCEPT AND ITS APPLICATION1

ABSTRACT: Storm water management is a concept being applied in many urban areas to deal with the increasing problems of storm runoff control and flood damage prevention. This paper introduces the concept and describes the recently completed storm water management program in Columbus, Georgia. Columbus has spent five years and over $200,000 in the development of their problem which includes several basic elements: soils inventory and analysis, hydrologic data collection, sediment and erosion control ordinance, storm water management handbook, urban flood simulation model, interdepartment coordination study, drainage problem categorization study, and a pilot basin study. The results of the pilot basin study are presented including example output from the urban simulation model. The computer output illustrates both the hydrologic-hydraulic and economic capabilities of the model.     

BACTERIAL RELATIONSHIPS IN STORMWATERS1

ABSTRACT: Data were developed within a three-year period for indicator bacteria and three species of bacterial pathogens following rural storm event hydrographs. The first flush concept was confirmed in all hydrographs. Bacterial density peaking occurred at or before the hydrograph peaks. FC and FS values were higher in more developed areas than the primary rural test site and their numerical ratios followed similar trends. Chlorine demand of storm waters varied between 8 and 16 mg/l and, the ozone requirement was greater than 32 mg/l in the same waters. Aftergrowth of total coliform bacteria occurred following chlorine and ozone doses of 16 mg/l and 32 mg/l respectively. Fecal coliform, fecal streptococci, Salmonella sp., and Pseudomonas sp. all were reduced to near detectable limits by the disinfectants up to 8 days. Staphylococcus sp. demonstrated a propensity to restablish their populations. Multiple regression analysis of the bacterial groups and species in storm waters suggested the fecal streptococci to have been the most useful group in evaluating bacterial storm water quality, with staphylocci have been closely related insofar as their statistical significance was concerned.     

ISOLATING THE RANDOM RAMSTORM COMPONENT FROM BASIN RESPONSE FACTORS IN RAINFALLRUNOFF DATA1

ABSTRACT: Gaged watersheds can provide information as to geomorphic, and geologic influence on the spatial variability of rainfall-runoff relationships. However, correlations between raingages distributed throughout the basin, and stream discharge are influenced by both storm patterns and drainage basin characteristics. Factor analysis has been applied to rainfall-runoff relationship to isolate the storm pattern from a basin response factor. Comparing two periods of time separated by eight years reveals relative stability in the rainfall attenuation (basin response) factor, while storm patterns for the two periods of record are quite disparate.